smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-125-generic] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke,
www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: KINGSTON SKC600/512G
Serial Number: HPN28A0200000666
LU WWN Device Id: 0 000000 000000000
Firmware Version: HP3414B5
User Capacity: 512 110 190 592 bytes [512 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
TRIM Command: Available
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-4 T13/BSR INCITS 529 revision 5
SATA Version is: SATA 3.2, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Mon Nov 11 13:20:13 2024 +07
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5d) SMART execute Offline immediate.
No Auto Offline data collection support.
Abort Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0002) Does not save SMART data before
entering power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 8) minutes.
Extended self-test routine
recommended polling time: ( 16) minutes.
SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x0032 100 100 050 Old_age Always - 0
5 Reallocated_Sector_Ct 0x0032 100 100 050 Old_age Always - 0
9 Power_On_Hours 0x0032 100 100 050 Old_age Always - 367
12 Power_Cycle_Count 0x0032 100 100 050 Old_age Always - 90
160 Unknown_Attribute 0x0032 100 100 050 Old_age Always - 0
161 Unknown_Attribute 0x0032 100 100 050 Old_age Always - 93
163 Unknown_Attribute 0x0032 100 100 050 Old_age Always - 0
164 Unknown_Attribute 0x0032 100 100 050 Old_age Always - 6
165 Unknown_Attribute 0x0032 100 100 050 Old_age Always - 10
166 Unknown_Attribute 0x0032 100 100 050 Old_age Always - 4
167 Unknown_Attribute 0x0032 100 100 050 Old_age Always - 6
168 Unknown_Attribute 0x0032 100 100 050 Old_age Always - 0
169 Unknown_Attribute 0x0032 100 100 050 Old_age Always - 100
175 Program_Fail_Count_Chip 0x0032 100 100 050 Old_age Always - 1023410176
176 Erase_Fail_Count_Chip 0x0032 100 100 050 Old_age Always - 1258
177 Wear_Leveling_Count 0x0032 100 100 050 Old_age Always - 30450
178 Used_Rsvd_Blk_Cnt_Chip 0x0032 100 100 050 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 050 Old_age Always - 13
194 Temperature_Celsius 0x0032 100 100 050 Old_age Always - 35
232 Available_Reservd_Space 0x0032 100 100 050 Old_age Always - 93
241 Total_LBAs_Written 0x0032 100 100 050 Old_age Always - 25684
242 Total_LBAs_Read 0x0032 100 100 050 Old_age Always - 56924
245 Unknown_Attribute 0x0032 100 100 050 Old_age Always - 35425
SMART Error Log Version: 1
ATA Error Count: 1
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1 occurred at disk power-on lifetime: 361 hours (15 days + 1 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 40 e8 20 b0 01 00 at LBA = 0x0001b020 = 110624
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 20 e8 20 b0 01 40 08 00:00:56.740 READ FPDMA QUEUED
60 20 e0 60 bd 08 40 08 00:00:56.740 READ FPDMA QUEUED
60 10 a8 88 9b 44 40 08 00:00:56.740 READ FPDMA QUEUED
60 20 a0 00 db 41 40 08 00:00:56.740 READ FPDMA QUEUED
60 10 20 28 46 d3 40 08 00:00:56.740 READ FPDMA QUEUED
SMART Self-test log structure revision number 0
Warning: ATA Specification requires self-test log structure revision number = 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
