LinuxMint.com.ru

rogoznik писал(а): ↑
19 мар 2024, 15:12

max писал(а): ↑
19 мар 2024, 15:05
но при этом получилось что при отключенном диске WD7502AAEX физически
При этом надо в fstab монтирование отключить, либо последнюю цифру в строке монтирования заменить на 0

так отключил, выше сообщением текущий fstab. и если при этом физически отключить диск, то система перестает грузиться

max писал(а): ↑
19 мар 2024, 15:05
при отключенном диске WD7502AAEX физически , система не грузится, виснет

И, как сказал rogoznik,

rogoznik писал(а): ↑
19 мар 2024, 15:12
надо в fstab монтирование отключить

max писал(а): ↑
19 мар 2024, 15:20
и если при этом физически отключить диск, то система перестает грузиться

чего то не договариваешь. Сколько систем на машине?

Slav164 писал(а): ↑
19 мар 2024, 17:43

max писал(а): ↑
19 мар 2024, 15:20
и если при этом физически отключить диск, то система перестает грузиться
чего то не договариваешь. Сколько систем на машине?

одна система на машине и всегда была одна, лет семь назад винду снес и поставил минт. Пару раз переставлял с нуля. Два диска дополнительных новые ставил,

Sharov писал(а): ↑
19 мар 2024, 15:55

max писал(а): ↑
19 мар 2024, 15:05
при отключенном диске WD7502AAEX физически , система не грузится, виснет
И, как сказал rogoznik,
rogoznik писал(а): ↑
19 мар 2024, 15:12
надо в fstab монтирование отключить

как я ответил выше, на оба дополнительных диска отключено монтирование в fstab, и сам с отключенными дисками fstab есть выше, и если физически отключить этот диск, то система перестает грузиться

Вопрос про зависания, а не про систему сейчас

max, запустить телегу из терминала и при зависании может быть чего видно будет

Slav164 писал(а): ↑
19 мар 2024, 18:29
max, запустить телегу из терминала и при зависании может быть чего видно будет

да, пробовал

./Telegram
qt.accessibility.atspi: Could not find accessible on path: "/org/a11y/atspi/accessible/2147483658"
qt.accessibility.atspi: Could not find accessible on path: "/org/a11y/atspi/accessible/2147483658"
qt.accessibility.atspi: Could not find accessible on path: "/org/a11y/atspi/accessible/2147483655"
qt.accessibility.atspi: Could not find accessible on path: "/org/a11y/atspi/accessible/2147483655"
QTextCursor::setPosition: Position '1' out of range
qt.gui.imageio.jpeg: Corrupt JPEG data: premature end of data segment
qt.gui.imageio.jpeg: Corrupt JPEG data: premature end of data segment
qt.gui.imageio.jpeg: Corrupt JPEG data: premature end of data segment
QTextCursor::setPosition: Position '1' out of range
Убито

Как завис, прибил

Есть подозрение что зависает на окне выбора пути/файла из библиотек QT

На программах из родного репозитария не замечено ни каких зависаний

max, xdg-desktop-portal-kde попробуй доустановить

Slav164 писал(а): ↑
19 мар 2024, 18:52
max, xdg-desktop-portal-kde попробуй доустановить

Поставил, так же зависает

max писал(а): ↑
19 мар 2024, 19:12

Slav164 писал(а): ↑
19 мар 2024, 18:52
max, xdg-desktop-portal-kde попробуй доустановить
Поставил, так же зависает

max писал(а): ↑
19 мар 2024, 18:09
Пару раз переставлял с нуля. Два диска дополнительных новые ставил,

А загрузочная запись на каком диске?
Можно скрин Gparted'а?

Sharov писал(а): ↑
20 мар 2024, 08:04

max писал(а): ↑
19 мар 2024, 18:09
Пару раз переставлял с нуля. Два диска дополнительных новые ставил,
А загрузочная запись на каком диске?
Можно скрин Gparted'а?

грузится с ssd, sda

не вижу как тут скрин прикрепить.

Да и вопрос сейчас про зависания

max писал(а): ↑
20 мар 2024, 09:20
не вижу как тут скрин прикрепить.

Кнопка "Добавить файлы", расположенная ниже блока "Быстрый ответ"

max писал(а): ↑
20 мар 2024, 09:20
Да и вопрос сейчас про зависания

телега ваще не показатель как посмотрю...
чудит она по полной, репортов на баги им пихают нынче по полной - как вывод проблема в телеге, а не в файловых операциях...
у меня она на видосиках вылетает, причём началось это с последней обновой...
странно что у тебя ничего в терминал не сыпит по ошибкам, у меня там полный ворох...

Код: Выделить всё

$ ./Telegram 
QPainter::begin: Paint device returned engine == 0, type: 2
QWidget::render: Cannot render with an inactive painter
qt.gui.imageio.jpeg: Corrupt JPEG data: premature end of data segment
qt.gui.imageio.jpeg: Corrupt JPEG data: premature end of data segment
qt.gui.imageio.jpeg: Corrupt JPEG data: premature end of data segment
qt.gui.imageio.jpeg: Corrupt JPEG data: premature end of data segment
[mov,mp4,m4a,3gp,3g2,mj2 @ 0x7f327ecb6640] Packet corrupt (stream = 1, dts = 116736).
[NULL @ 0x7f1c7eee2840] Invalid NAL unit size (102509 > 4080).
[NULL @ 0x7f1c7eee2840] missing picture in access unit with size 4084
[mov,mp4,m4a,3gp,3g2,mj2 @ 0x7f327ee5a640] Packet corrupt (stream = 0, dts = 1926925).
[NULL @ 0x7f1c7ed92440] Invalid NAL unit size (83690 > 2538).
[NULL @ 0x7f1c7ed92440] missing picture in access unit with size 2570
[libvpx-vp9 @ 0x7f1c7ed94c40] v1.13.0
[libvpx-vp9 @ 0x7f1c7ed94c40] v1.13.0
[libvpx-vp9 @ 0x7f1c7ed90440] v1.13.0
[libvpx-vp9 @ 0x7f1c7ed90440] v1.13.0
Ошибка сегментирования (образ памяти сброшен на диск)

$ ./Telegram 
QPainter::begin: Paint device returned engine == 0, type: 2
QWidget::render: Cannot render with an inactive painter
qt.gui.imageio.jpeg: Corrupt JPEG data: premature end of data segment
  OpenType support missing for "DAOpenSansSemibold", script 11
  OpenType support missing for "davazirmedium", script 11
  OpenType support missing for "DAOpenSansSemibold", script 16
  OpenType support missing for "davazirmedium", script 16
[AVHWDeviceContext @ 0x7fb2dc8955c0] Failed to initialise VAAPI connection: -1 (unknown libva error).
[AVHWDeviceContext @ 0x7fb2dc8b3340] Failed to initialise VAAPI connection: -1 (unknown libva error).
[AVHWDeviceContext @ 0x7fb2dc89d140] Failed to initialise VAAPI connection: -1 (unknown libva error).
[AVHWDeviceContext @ 0x7fb2dc8a8e40] Failed to initialise VAAPI connection: -1 (unknown libva error).
[AVHWDeviceContext @ 0x7fb2dc982e40] Failed to initialise VAAPI connection: -1 (unknown libva error).
[AVHWDeviceContext @ 0x7fb2dc9184c0] Failed to initialise VAAPI connection: -1 (unknown libva error).
[AVHWDeviceContext @ 0x7fb2dbd00340] Failed to initialise VAAPI connection: -1 (unknown libva error).
[AVHWDeviceContext @ 0x7fb2dbd00340] Failed to initialise VAAPI connection: -1 (unknown libva error).
qt.gui.imageio.jpeg: Corrupt JPEG data: premature end of data segment
qt.gui.imageio.jpeg: Corrupt JPEG data: premature end of data segment
qt.gui.imageio.jpeg: Corrupt JPEG data: premature end of data segment
qt.gui.imageio.jpeg: Corrupt JPEG data: premature end of data segment
qt.gui.imageio.jpeg: Corrupt JPEG data: premature end of data segment
qt.gui.imageio.jpeg: Corrupt JPEG data: premature end of data segment
qt.gui.imageio.jpeg: Corrupt JPEG data: premature end of data segment
QTextCursor::setPosition: Position '77' out of range
QTextCursor::setPosition: Position '77' out of range
qt.gui.imageio.jpeg: Corrupt JPEG data: premature end of data segment
qt.gui.imageio.jpeg: Corrupt JPEG data: premature end of data segment
qt.gui.imageio.jpeg: Corrupt JPEG data: premature end of data segment
[mov,mp4,m4a,3gp,3g2,mj2 @ 0x7fb9db69ae40] Packet corrupt (stream = 0, dts = 524000).
[NULL @ 0x7faadb7f2840] Invalid NAL unit size (118844 > 3202).
[NULL @ 0x7faadb7f2840] missing picture in access unit with size 3206
qt.gui.imageio.jpeg: Corrupt JPEG data: premature end of data segment
[mov,mp4,m4a,3gp,3g2,mj2 @ 0x7fb9db6cd240] Packet corrupt (stream = 0, dts = 4590000).
[NULL @ 0x7faadb733840] Invalid NAL unit size (28094 > 40).
[NULL @ 0x7faadb733840] missing picture in access unit with size 83
qt.gui.imageio.jpeg: Corrupt JPEG data: premature end of data segment
[AVHWDeviceContext @ 0x7fb2dca13a40] Failed to initialise VAAPI connection: -1 (unknown libva error).
[AVHWDeviceContext @ 0x7fb2dc9c00c0] Failed to initialise VAAPI connection: -1 (unknown libva error).
[AVHWDeviceContext @ 0x7fb2dc9c00c0] Failed to initialise VAAPI connection: -1 (unknown libva error).
qt.gui.imageio.jpeg: Corrupt JPEG data: premature end of data segment
qt.gui.imageio.jpeg: Corrupt JPEG data: premature end of data segment
qt.gui.imageio.jpeg: Corrupt JPEG data: premature end of data segment
qt.gui.imageio.jpeg: Corrupt JPEG data: premature end of data segment
[mov,mp4,m4a,3gp,3g2,mj2 @ 0x7fb9dba18e40] Packet corrupt (stream = 1, dts = 2466000).
[NULL @ 0x7faadb756840] Invalid NAL unit size (8127 > 3327).
[NULL @ 0x7faadb756840] missing picture in access unit with size 3331
[AVHWDeviceContext @ 0x7fb2dc9c8ac0] Failed to initialise VAAPI connection: -1 (unknown libva error).
Убито

Sharov писал(а): ↑
20 мар 2024, 08:04

max писал(а): ↑
19 мар 2024, 18:09
Пару раз переставлял с нуля. Два диска дополнительных новые ставил,
А загрузочная запись на каком диске?
Можно скрин Gparted'а?

Это что за ошибка при выключении? после нее компьютер выключается сразу

max писал(а): ↑
21 мар 2024, 22:50
Это что за ошибка при выключении? после нее компьютер выключается сразу

Это система часть файловых систем отмонтировать не может во время соответствующего этапа. По причине отсутствия - то что выше по иерархии уже остановлено. Т.к. это RO образ базовой (начальной) системы, и виртуальная FS с датчиками/переменными ядра - пофиг в общем-то.

slant писал(а): ↑
18 мар 2024, 21:51

max писал(а): ↑
18 мар 2024, 08:39
Диски сканировал badblocks на предмет ошибок, ошибки не обнаружены
SMART смотреть надо сначала, а не badblock использовать. Проблемы с железом он может и не показать. sudo smartctl -a /dev/sdX (где sdX - подозреваемый диск)

И еще имеет смысл смотреть журнал системы после попытки такой записи - journalctl -b
Есть хороший шанс обнаружить источник, если проблема чисто программная.

sudo smartctl -a /dev/sda
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-101-generic] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family: Indilinx Barefoot_2/Everest/Martini based SSDs
Device Model: OCZ-VERTEX4
Serial Number: OCZ-M1R145D527WWD65J
LU WWN Device Id: 5 e83a97 0288f45d5
Firmware Version: 1.5
User Capacity: 128 035 676 160 bytes [128 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
TRIM Command: Available
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sat Mar 23 01:42:03 2024 +07
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x1d) SMART execute Offline immediate.
No Auto Offline data collection support.
Abort Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x00) Error logging NOT supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 0) minutes.
Extended self-test routine
recommended polling time: ( 0) minutes.

SMART Attributes Data Structure revision number: 18
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x0000 005 000 000 Old_age Offline - 5
3 Spin_Up_Time 0x0000 100 100 000 Old_age Offline - 0
4 Start_Stop_Count 0x0000 100 100 000 Old_age Offline - 0
5 Reallocated_Sector_Ct 0x0000 100 100 000 Old_age Offline - 0
9 Power_On_Hours 0x0000 100 100 000 Old_age Offline - 26259
12 Power_Cycle_Count 0x0000 100 100 000 Old_age Offline - 2693
232 Lifetime_Writes 0x0000 100 100 000 Old_age Offline - 43001201734
233 Media_Wearout_Indicator 0x0000 094 000 000 Old_age Offline - 94

SMART Error Log not supported

Warning! SMART Self-Test Log Structure error: invalid SMART checksum.
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]

Selective Self-tests/Logging not supported

sudo smartctl -a /dev/sdb
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-101-generic] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.14 (AF)
Device Model: ST500DM002-1BD142
Serial Number: W2AAG4G9
LU WWN Device Id: 5 000c50 04ae70d9f
Firmware Version: KC65
User Capacity: 500 107 862 016 bytes [500 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sat Mar 23 01:43:26 2024 +07
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 592) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 78) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 112 099 006 Pre-fail Always - 46464880
3 Spin_Up_Time 0x0003 100 098 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 099 099 020 Old_age Always - 1054
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 077 060 030 Pre-fail Always - 8705602964
9 Power_On_Hours 0x0032 076 076 000 Old_age Always - 21577
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 901
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 099 000 Old_age Always - 11 11 11
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 061 050 045 Old_age Always - 39 (Min/Max 24/39)
194 Temperature_Celsius 0x0022 039 050 000 Old_age Always - 39 (0 20 0 0 0)
195 Hardware_ECC_Recovered 0x001a 034 022 000 Old_age Always - 46464880
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 21580h+13m+26.091s
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 3657176121
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 828211974

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

sudo smartctl -a /dev/sdc
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-101-generic] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar Black
Device Model: WDC WD7502AAEX-00Y9A0
Serial Number: WD-WCAW31804102
LU WWN Device Id: 5 0014ee 205cf5c88
Firmware Version: 05.01D05
User Capacity: 750 156 374 016 bytes [750 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Sat Mar 23 01:44:33 2024 +07
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (12780) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 133) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x3035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 199 198 051 Pre-fail Always - 13779
3 Spin_Up_Time 0x0027 168 164 021 Pre-fail Always - 4591
4 Start_Stop_Count 0x0032 093 093 000 Old_age Always - 7783
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 042 042 000 Old_age Always - 42953
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 095 095 000 Old_age Always - 5275
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 200
193 Load_Cycle_Count 0x0032 198 198 000 Old_age Always - 7582
194 Temperature_Celsius 0x0022 103 088 000 Old_age Always - 44
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 199 000 Old_age Offline - 162

SMART Error Log Version: 1
ATA Error Count: 226 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 226 occurred at disk power-on lifetime: 27542 hours (1147 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 91 c2 ea ea Error: UNC at LBA = 0x0aeac291 = 183157393

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 00 b8 c1 ea ea 08 10:31:12.144 READ DMA
c8 00 00 b8 c0 ea ea 08 10:31:12.144 READ DMA
c8 00 00 b8 bf ea ea 08 10:31:12.143 READ DMA
ec 00 01 00 00 00 00 08 10:31:12.140 IDENTIFY DEVICE

Error 225 occurred at disk power-on lifetime: 27542 hours (1147 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 91 c2 ea ea Error: UNC at LBA = 0x0aeac291 = 183157393

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 00 b8 c1 ea ea 08 10:30:54.294 READ DMA
c8 00 00 b8 c0 ea ea 08 10:30:54.293 READ DMA
c8 00 00 b8 bf ea ea 08 10:30:54.292 READ DMA
c8 00 00 b8 be ea ea 08 10:30:54.292 READ DMA
c8 00 00 b8 bd ea ea 08 10:30:54.291 READ DMA

Error 224 occurred at disk power-on lifetime: 27538 hours (1147 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 91 c2 ea ea Error: UNC 8 sectors at LBA = 0x0aeac291 = 183157393

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 90 c2 ea ea 08 05:46:44.096 READ DMA
c8 00 08 80 c2 ea ea 08 05:46:44.085 READ DMA

Error 223 occurred at disk power-on lifetime: 27537 hours (1147 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 28 91 c2 ea ea Error: UNC 40 sectors at LBA = 0x0aeac291 = 183157393

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 28 80 c2 ea ea 08 05:22:43.540 READ DMA
c8 00 08 68 c2 ea ea 08 05:22:43.527 READ DMA

Error 222 occurred at disk power-on lifetime: 27536 hours (1147 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 88 91 c2 ea ea Error: UNC 136 sectors at LBA = 0x0aeac291 = 183157393

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 88 30 c2 ea ea 08 03:53:33.922 READ DMA
c8 00 50 e0 c1 ea ea 08 03:53:33.922 READ DMA
c8 00 08 d8 c1 ea ea 08 03:53:33.920 READ DMA
c8 00 10 b8 c1 ea ea 08 03:53:33.920 READ DMA
c8 00 08 a0 c1 ea ea 08 03:53:33.919 READ DMA

SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed: read failure 90% 26186 183157393
# 2 Extended offline Completed: read failure 90% 26175 183157393

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

sudo smartctl -a /dev/sdd
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-101-generic] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family: Western Digital Blue
Device Model: WDC WD40EZRZ-00GXCB0
Serial Number: WD-WCC7K0ZH7D4R
LU WWN Device Id: 5 0014ee 2bb379003
Firmware Version: 80.00A80
User Capacity: 4 000 787 030 016 bytes [4,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-3 T13/2161-D revision 5
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Sat Mar 23 01:45:29 2024 +07
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (44340) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 470) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x3035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 166 165 021 Pre-fail Always - 6691
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 197
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 097 097 000 Old_age Always - 2597
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 197
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 16
193 Load_Cycle_Count 0x0032 199 199 000 Old_age Always - 3148
194 Temperature_Celsius 0x0022 118 112 000 Old_age Always - 32
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

Диску который обозначен как sdc - WD7502AAEX-00Y9A0 весьма нездорово...
Однозначный диагноз поставить нельзя (с такими симптомами/показателями несколько вариантов подходят), но что он нездоров - 100%. Менять нужно, и чем быстрее - тем лучше. Очень возможно, что идет активное разрушение технической информации (маркеры дорожек, прошивка), может перестать включаться в любой момент. Но может проработать (с глюками) еще некоторое время. В домашних условиях лечению не подлежит, в сервисе - скорее всего тоже, или будет дорого (нерентабельно).
Такие проблемы у диска как раз могут давать "подвисания" при обращении к нему, при видимой сохранности информации (до поры).

LinuxMint.com.ru

зависают файловые операции

зависают файловые операции

зависают файловые операции

зависают файловые операции

зависают файловые операции

зависают файловые операции

зависают файловые операции

зависают файловые операции

зависают файловые операции

зависают файловые операции

зависают файловые операции

зависают файловые операции

зависают файловые операции

зависают файловые операции

зависают файловые операции

зависают файловые операции

зависают файловые операции

зависают файловые операции

зависают файловые операции

зависают файловые операции

зависают файловые операции