sudo smartctl -x /dev/sdc
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.13.0-39-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.11
Device Model: ST31000333AS
Serial Number: *****
LU WWN Device Id: *****
Firmware Version: CC1F
User Capacity: 1 000 204 886 016 bytes [1,00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Sat Jul 14 16:15:18 2018 MSK
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM level is: 254 (maximum performance), recommended: 254
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Unknown
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 617) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 203) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-- 114 099 006 - 72100782
3 Spin_Up_Time PO---- 098 094 000 - 0
4 Start_Stop_Count -O--CK 088 088 020 - 12374
5 Reallocated_Sector_Ct PO--CK 100 100 036 - 2
7 Seek_Error_Rate POSR-- 084 060 030 - 273052495
9 Power_On_Hours -O--CK 070 070 000 - 26341
10 Spin_Retry_Count PO--C- 100 100 097 - 10
12 Power_Cycle_Count -O--CK 096 037 020 - 4134
184 End-to-End_Error -O--CK 062 062 099 NOW 38
187 Reported_Uncorrect -O--CK 100 100 000 - 0
188 Command_Timeout -O--CK 100 097 000 - 73015624450
189 High_Fly_Writes -O-RCK 001 001 000 - 257
190 Airflow_Temperature_Cel -O---K 050 037 045 Past 50 (Min/Max 28/52 #216)
194 Temperature_Celsius -O---K 050 063 000 - 50 (0 16 0 0 0)
195 Hardware_ECC_Recovered -O-RC- 050 022 000 - 72100782
197 Current_Pending_Sector -O--C- 100 100 000 - 0
198 Offline_Uncorrectable ----C- 100 100 000 - 0
199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 23
240 Head_Flying_Hours ------ 100 253 000 - 25336 (21 195 0)
241 Total_LBAs_Written ------ 100 253 000 - 2395209249
242 Total_LBAs_Read ------ 100 253 000 - 652933921
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 GPL,SL R/O 1 Summary SMART error log
0x02 GPL,SL R/O 5 Comprehensive SMART error log
0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log
0x06 GPL,SL R/O 1 SMART self-test log
0x07 GPL,SL R/O 1 Extended self-test log
0x09 GPL,SL R/W 1 Selective self-test log
0x10 GPL,SL R/O 1 SATA NCQ Queued Error log
0x11 GPL,SL R/O 1 SATA Phy Event Counters log
0x21 GPL,SL R/O 1 Write stream error log
0x22 GPL,SL R/O 1 Read stream error log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa1 GPL,SL VS 20 Device vendor specific log
0xa2 GPL VS 2248 Device vendor specific log
0xa8 GPL,SL VS 129 Device vendor specific log
0xa9 GPL,SL VS 1 Device vendor specific log
0xb0 GPL VS 2928 Device vendor specific log
0xbe-0xbf GPL VS 65535 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (5 sectors)
Device Error Count: 8796 (device log contains only the most recent 20 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 8796 [15] occurred at disk power-on lifetime: 10024 hours (417 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 71 00 0e 00 00 00 00 1d 80 e0 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ec 00 00 00 01 00 00 00 00 00 00 a0 00 00:06:20.139 IDENTIFY DEVICE
ff 00 00 00 00 00 00 00 00 00 00 00 00 00:06:20.099 [VENDOR SPECIFIC]
00 00 00 00 00 00 00 00 00 00 00 00 ff 00:06:20.099 NOP [Abort queued commands]
ff 00 00 00 00 00 00 00 00 00 00 00 00 00:06:17.607 [VENDOR SPECIFIC]
00 00 00 00 00 00 00 00 00 00 00 00 ff 00:06:17.607 NOP [Abort queued commands]
Error 8795 [14] occurred at disk power-on lifetime: 10024 hours (417 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 71 00 0e 00 00 00 00 1d 80 40 00 Device Fault; Error: ABRT at LBA = 0x00001d80 = 7552
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 00 01 00 00 04 21 00 38 38 40 00 00:05:51.378 WRITE FPDMA QUEUED
ef 00 90 00 03 00 00 00 00 00 00 00 00 00:05:51.353 SET FEATURES [Disable SATA feature]
ef 00 02 00 00 00 00 00 00 00 00 00 00 00:05:51.328 SET FEATURES [Enable write cache]
00 00 00 00 00 00 00 00 00 00 00 00 ff 00:05:51.211 NOP [Abort queued commands]
61 00 00 01 00 00 04 20 00 38 38 40 00 00:05:51.211 WRITE FPDMA QUEUED
Error 8794 [13] occurred at disk power-on lifetime: 10024 hours (417 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 71 00 0e 00 00 00 00 1d 80 40 00 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 90 00 03 00 00 00 00 00 00 00 00 00:05:51.353 SET FEATURES [Disable SATA feature]
ef 00 02 00 00 00 00 00 00 00 00 00 00 00:05:51.328 SET FEATURES [Enable write cache]
00 00 00 00 00 00 00 00 00 00 00 00 ff 00:05:51.211 NOP [Abort queued commands]
61 00 00 01 00 00 04 20 00 38 38 40 00 00:05:51.211 WRITE FPDMA QUEUED
61 00 00 01 00 00 04 1f 00 38 38 40 00 00:05:51.107 WRITE FPDMA QUEUED
Error 8793 [12] occurred at disk power-on lifetime: 10024 hours (417 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 71 00 0e 00 00 00 00 1d 80 40 00 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 02 00 00 00 00 00 00 00 00 00 00 00:05:51.328 SET FEATURES [Enable write cache]
00 00 00 00 00 00 00 00 00 00 00 00 ff 00:05:51.211 NOP [Abort queued commands]
61 00 00 01 00 00 04 20 00 38 38 40 00 00:05:51.211 WRITE FPDMA QUEUED
61 00 00 01 00 00 04 1f 00 38 38 40 00 00:05:51.107 WRITE FPDMA QUEUED
61 00 00 01 00 00 04 1e 00 38 38 40 00 00:05:51.107 WRITE FPDMA QUEUED
Error 8792 [11] occurred at disk power-on lifetime: 10024 hours (417 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 71 00 0e 00 00 00 00 1d 80 40 00 Device Fault; Error: ABRT at LBA = 0x00001d80 = 7552
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 04 1f 00 34 98 40 00 00:05:51.103 READ FPDMA QUEUED
ef 00 90 00 03 00 00 00 00 00 00 00 00 00:05:51.081 SET FEATURES [Disable SATA feature]
ef 00 02 00 00 00 00 00 00 00 00 00 00 00:05:51.015 SET FEATURES [Enable write cache]
00 00 00 00 00 00 00 00 00 00 00 00 ff 00:05:50.938 NOP [Abort queued commands]
60 00 00 00 80 00 04 72 00 31 30 40 00 00:05:50.938 READ FPDMA QUEUED
Error 8791 [10] occurred at disk power-on lifetime: 10024 hours (417 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 71 00 0e 00 00 00 00 1d 80 40 00 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 90 00 03 00 00 00 00 00 00 00 00 00:05:51.081 SET FEATURES [Disable SATA feature]
ef 00 02 00 00 00 00 00 00 00 00 00 00 00:05:51.015 SET FEATURES [Enable write cache]
00 00 00 00 00 00 00 00 00 00 00 00 ff 00:05:50.938 NOP [Abort queued commands]
60 00 00 00 80 00 04 72 00 31 30 40 00 00:05:50.938 READ FPDMA QUEUED
60 00 00 00 80 00 04 53 00 37 98 40 00 00:05:50.834 READ FPDMA QUEUED
Error 8790 [9] occurred at disk power-on lifetime: 10024 hours (417 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 71 00 0e 00 00 00 00 1d 80 40 00 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 02 00 00 00 00 00 00 00 00 00 00 00:05:51.015 SET FEATURES [Enable write cache]
00 00 00 00 00 00 00 00 00 00 00 00 ff 00:05:50.938 NOP [Abort queued commands]
60 00 00 00 80 00 04 72 00 31 30 40 00 00:05:50.938 READ FPDMA QUEUED
60 00 00 00 80 00 04 53 00 37 98 40 00 00:05:50.834 READ FPDMA QUEUED
60 00 00 00 08 00 04 67 00 37 10 40 00 00:05:50.834 READ FPDMA QUEUED
Error 8789 [8] occurred at disk power-on lifetime: 10024 hours (417 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 71 00 0e 00 00 00 00 1d 80 40 00 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 90 00 03 00 00 00 00 00 00 00 00 00:05:50.828 SET FEATURES [Disable SATA feature]
ef 00 02 00 00 00 00 00 00 00 00 00 00 00:05:50.815 SET FEATURES [Enable write cache]
00 00 00 00 00 00 00 00 00 00 00 00 ff 00:05:50.678 NOP [Abort queued commands]
60 00 00 00 08 00 04 1f 00 34 98 40 00 00:05:50.678 READ FPDMA QUEUED
61 00 00 01 00 00 04 27 00 38 38 40 00 00:05:50.574 WRITE FPDMA QUEUED
SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 522 (0x020a)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 50 Celsius
Power Cycle Min/Max Temperature: 28/52 Celsius
Lifetime Min/Max Temperature: 16/63 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 14/55 Celsius
Min/Max Temperature Limit: 10/60 Celsius
Temperature History Size (Index): 128 (92)
Index Estimated Time Temperature Celsius
93 2018-07-14 14:08 51 ********************************
... ..(117 skipped). .. ********************************
83 2018-07-14 16:06 51 ********************************
84 2018-07-14 16:07 50 *******************************
... ..( 7 skipped). .. *******************************
92 2018-07-14 16:15 50 *******************************
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x000a 2 6 Device-to-host register FISes sent due to a COMRESET
0x0001 2 0 Command failed due to ICRC error
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
